Special Features:
1.Dual speakers and dual frequency. Combines fixed frequency, wide frequency sweep ultrasonic, and audible warning sound waves to prevent martens, weasels, and other animals from developing tolerance, ensuring strong repellent effects
2.Easy to install. Secure the device with cable ties or magnetic mounts. It can be mounted on walls, in gardens, garages, vehicle engine compartments, and other places
3.Multi functional. Prevents martens and other rodents from entering the car engine compartment to chew wiring harnesses and rubber hoses, avoiding vehicle circuit failures. It can also be placed in garages, carports, and attics to prevent raccoons and small wild animals from lingering around the parking area
4.Working principle. The device emits sweep and fixed frequency ultrasonic waves combined with warning sounds to stimulate the hearing of wild animals and drive them away. With PIR infrared sensing that triggers only when animals approach. Certain modes synchronize strobe lights to enhance the scare effect
5.Note: Not for sale on Amazon Germany
Detailed Functions of the Three Modes:
Mode 1 (Button O): Automatic Ultrasonic + Sound Playback Indicator light: Green. Infrared PIR sensing and the strobe flash are disabled; the device continuously cycles sound and ultrasonic output
To prevent animals from developing habituation, both the operating duration and the pause interval follow a dynamic random cycle:
– Sound + ultrasonic output duration: varies dynamically between 3 and 10 seconds (minimum 3 s, maximum 10 s)
– Pause interval: varies dynamically from 45 seconds to 3 minutes
– Output signal: directional 25 kHz ultrasound, together with a second ultrasonic channel running an automatic 20-48 kHz frequency sweep
Mode 2 (Button I): Light ON + Infrared PIR Sensing Enabled
Indicator light: Green
When animal movement is detected by the infrared PIR (passive infrared heat) sensor, one working cycle is triggered: the strobe light and ultrasonic output run for approximately 12 seconds, pause for 10 seconds, then run another approximately 12-second cycle, with the strobe flashing in a varied pattern. The ultrasonic output is activated at the same time: one directional channel at 25 kHz, and the other channel running an automatic frequency sweep at 20-48 kHz
Mode 3 (Button II): Light OFF, PIR Motion Sensor Enabled
Indicator light: Green
When animal movement is detected by the infrared PIR sensor, one working cycle is triggered: the ultrasonic output runs for approximately 12 seconds, pauses for 10 seconds, then runs another approximately 12-second cycle. The ultrasonic output is activated at the same time: one directional channel at 25 kHz, and the other channel running an automatic frequency sweep at 20-48 kHz
Note:
For the engine compartment, Mode 2 (motion activated without light) is highly recommended
For open air parking spaces and courtyards, Mode 1 (light and motion activated) is recommended
For long term vacant attics, Mode 0 (automatic cycle mode) is recommended
Low-Voltage Protection:
Under car-battery power, if the detected voltage is below 11.7 V and remains so for 10 seconds, the system determines that the battery is flat (low battery); the indicator light turns red and the system stops working. When the battery voltage rises to above 11.8 V, the device returns to the currently selected mode.This prevents the car battery from being drained. When the product is powered through the plug connection, no car-battery voltage check is required and the product continues to operate normally
When powered by the vehicle battery, the device shuts off if vehicle movement is detected:
Under car-battery power, if the detected voltage is ≥13.3 V and remains so for 5 seconds, the system determines that the car engine has started, and the device stops working. This condition applies to all three modes. When the detected voltage is below 12.7 V but above 11.7 V and remains so for 60 seconds, the device returns to the currently selected mode, and the system determines that the engine has been switched off
Power Supply: The product can be powered either via USB or from a car battery
Accessories:
(1) 2 cable ties (5 mm wide x 15 cm long)
(2) 2 magnetic strips (7.9*2*0.2cm; one is to be attached to the product; the other can be placed wherever the user chooses)
(3) 2 cables: one 1.5 m cable with a USB connector at one end and positive/negative leads at the other; one 2 m cable with a USB connector at one end and a plug connector at the other
Power Input Options:
1. Power supply type 1: +5 V @ 2 A 2. Power supply type
2: car battery, 12.2-14.8 V @ 1.5 A
























































